Copyright © 2025 Novo Surgical Inc. All Rights Reserved
Diamond Pin Wire Cutter
Details
Novo Surgical’s Diamond Pin Wire Cutter is a specially designed instrument crafted for use in cutting wire. Many different neurosurgical and orthopedic procedures require the insertion of wire to give the areas additional stability and this cutter can be used to clip these at the desired length. Not only can this instrument be used to trim wire but also surgical pins. Fracture repair and other bone repair surgeries has to be set with pins that also need to be trimmed using this instrument. This instrument is available in two designs: stainless steal or tungsten carbide both of which can cup up to a diameter of 2.0 mm.
Please note that website images are often representative of the product family and may not conform to the exact specifications or features of the item you select. The final specifications will match the description of the specific catalog item you select. Please review such specifications in the item description to ensure the correct product is ordered.
More Information
| Manufacturer | Novo Surgical Inc. |
|---|---|
| Grade | Premium Operating Room |
| Material Finish | Stainless Steel/Tungsten Carbide |
| Specialty | NEURO, ORTHO & SPINE/WIRE & PIN MANAGEMENT INSTRUMENTS/PIN CUTTERS |
| Sterility | Non-Sterile |
| Unit Of Measurement | Each |
| Usage | Reusable |
| Countries for Sale | USA, CANADA |
Warranty
Novo Surgical instruments are guaranteed to be free from defects in materials and workmanship when used under normal conditions for their intended surgical purpose. Any Novo Surgical instrument that is determined to be defective will, at Novo Surgical's discretion, be repaired or replaced. Normal wear and tear and/or instrument misuse, including improper use or inadequate maintenance, are not covered under the manufacturer's warranty. All Novo Surgical instruments are warranted only to the original purchaser. This instrument is intended to be used only for the specific purpose for which it was designed. It is the responsibility of clinicians and sterilization professionals to familiarize themselves with proper techniques for using and caring for this instrument. For more detailed instrument care recommendations, please visit the Instrument Care section of our website.
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. By purchasing this product, you warrant that you are either a medical practitioner or purchasing on behalf of a licensed medical facility, educational or government agency, or a customer that sells these products to such institutions. After your order is placed, we may request you to provide additional information, including, but not limited to, the name and address of healthcare facility or the National Provider Identifier (NPI) number for the provider you are ordering on behalf of. Please note that the lack of a satisfactory response may result in the delay or cancellation of your order.
Related Products
-
Corwin Wire Twistertungsten carbide, serrated jaws, long tips, 6-1/4" (15.9 cm) -
Flat Nose Pliersserrated jaws, 5-1/2" (14.0 cm) -
Side Wire/Pin Cuttertungsten carbide jaws, double-action, angled jaws -
Cable Cuttertungsten carbide jaws, maximum capacity 2.0 mm, 7" (18.0 cm) -
Parallel Pliers & Wire Cutterdouble-action, 7-1/4" (18.4 cm) -
Needle Nose Pliersstandard, 5-1/2" (14.0 cm) -
Wire Pulling Forcepsmax capacity 1.0 mm, 6-1/2" (16.5 cm) -
Flat Nose Pliers & Cutter3.5mm tip, cuts 0.2 mm to 1.5 mm wire, 6-1/2" (16.5 cm) -
Pin Cutterend cutting, stainless -
Front & Side Wire Cuttertungsten carbide jaws, double-action, 1/16" (1.7 mm) maximum capacity, 7-1/8" (18.1 cm) -
Hercules-Type Cable Cutterreplaceable tungsten carbide blades, for 1.0 mm to 2.0 mm cables, 7" (18.0 cm) -
Locking Pliersreinforced jaw hinge, self-locking lever w/ adjustment screw & one-handed quick release -
Side Wire/Pin Cuttertungsten carbide jaws, double-action, 3/32" (2.5mm) maximum capacity, 9" (23.0 cm) -
Long Jaw Needle Nose Pliers2-1/4" jaw length, 2.0 mm tip, 7" (17.8 cm) -
Pin Cutterend cutting, tungsten carbide -
Wire Twistercross-serrated nose, blunt jaws, tungsten carbide inserts, 8-1/4" (21.0 cm) -
Cannulated Pin Cutterend cutting, max cutting capacity 1/16" (1.7 mm), 7-1/2" (19.0 cm) -
Wire Tightener4-3/4" (12.0 cm) -
Hercules-Type Wire Cutterfor drill-wires of max 2.2 mm, replaceable tungsten carbide blades & replaceable rubber jaws, 7" (18.0 cm) -
End Cuttertungsten carbide jaws, double-action, maximum capacity 3⁄32" (2.5mm), 8-1/2" (21.6 cm) -
Blunt Jaw Pliers5-1/2" (14.0 cm) -
Wire Extraction Pliers/Forcepstungsten carbide jaws, double-action, 7" (17.8 cm) -
Berry Sternal Needle Holder & Wire Twistertungsten carbide inserts, heavy pattern, 6.0 mm jaws, 7-3/4" (19.5 cm) -
Flat Nose Pliersslender jaws, 2.0 mm tip, 6" (15.2 cm) -
Rubio Needle Holder & Wire Twistertungsten carbide, serrated jaws, snub nose -
Hercules-Type Extraction Forcepstungsten carbide jaws, 7" (18.0 cm) -
K-Wire Side Cuttertungsten carbide jaws , cuts up to 0.047" (1.1 mm) diameter hard wire, 6" (15.2 cm) -
Parallel Pliersmaximum capacity 1/2", parallel grooved 10.0 mm jaws, 7" (17.8 cm) -
Needle Nose Pliersdelicate, 4-3/4" (12.1 cm) -
Wire Twister & Tightener6-1/4" (15.9 cm) -
Needle Nose Pliersdelicate, jaws w/ groove, 2.0 mm tip, 5-1/2" (14.0 cm) -
Side Wire/Pin Cutterside cutting, tungsten carbide jaws -
Double Action Pin Cutterside cutting maximum capacity 1⁄8" (3.2mm), 9-1/2" (24.1 cm) -
Hercules-Type Front & Side Cutterreplaceable tungsten carbide blades w/ integrated rubber jaws, for max 1.6 mm drill wire, 7" (17.8 cm) -
Slip Joint Pliersstainless steel -
Wire Twisting Forceps13.0 mm jaw length, 5-1/2" (14.0 cm) -
Narrow Nose Wire Pulling Forceps3mm tip, 7-1/2" (19.1 cm) -
Pin Cutterside cutting, stainless -
Medium Wire Twistertungsten carbide inserts, 6-3/4" (17.1 cm) -
Flush Wire Cuttertungsten carbide jaws, double-action, front & side cutting, cuts up to 1/16" (1.7 mm) diameter hard wire, 7" (17.8 cm) -
Loute Wire Tightener8-1/2" (22.0 cm) -
Needle Nose Locking Pliersreinforced jaw hinge, self-locking lever w/ adjustment screw & one-handed quick release -
End Cuttertungsten carbide jaws, maximum capacity 1/16" (1.7mm), 6" (15.0 cm) -
Lineman Pliersstainless steel, side-cutting, maximum capacity 1.6 mm, 8-1/2" (21.6 cm) -
Pin Cutterside cutting, tungsten carbide -
Novo Sternal Needle Holder & Wire Twistertungsten carbide inserts, 7" (17.8 cm) -
Pin Pullertungsten carbide, serrated, 3.0 mm tip, 5-1/2" (14.0 cm) -
Wire Twistertungsten carbide inserts, 6" (15.2 cm) -
Delicate Wire Cuttertungsten carbide jaws , cuts up to 1/36" (0.7 mm) diameter hard wire, 4-3/4" (12.1 cm) -
Lineman Plierstungsten carbide, side-cutting, maximum capacity 1.6 mm, w/ tungsten carbide inserts, 8-1/2" (21.6 cm) -
Flat Nose K-Wire Pliersserrated jaws, 7" (17.8 cm)